A Closer Look.
Remote Control for Motion Sensor Programming for NextGen III & IV Parking Lot Lights, Corvus II, Durado III & IV Wall Packs, Pegasus II & III High Bay Bulbs, Aries III & IV Corn Bulbs, Norani Series Wall Light and Titan V & VI High Bay Lights - Easily Program the Motion Sensor after Install
Note: 1 remote can program all lights. So you only need 1-2 (a spare) for each installation. Please purchase at least 1 or the lights may not operate as desired. Default sensor settings without using the remote are 70% brightness for 10 seconds with motion detected followed by an infinite stand-by time at 10% brightness, 20% sensitivity and the daylight sensor is disabled.
Motion Sensor Remote Spec Sheet: Motion Sensor Remote Control Instructions and Spec Sheet
Motion Sensor Specific Spec Sheet: Motion Sensor Spec Sheet (Motion sensor sold separately)
VIDEO ON HOW TO PROGRAM. WATCH AND PRACTICE BEFORE INSTALL
How to use the Nextgen 3 Motion Sensor Light Remote Control to Program - Instructional video
How to use the Nextgen 3 Motion Sensor Light Remote control to program - Instructional video on programming the nextgen III series LED Parking lot lights The video below is a 17 minute case study on NextGen 3 Motion sensor lights , but this section at 12:12 shows some more programming tips. LED Parking Lot Lights Install - Before & After - NextGen 3 LEDs With Motion - Aerial Drone Shots
LED Parking Lot Lights Install - Before & after - NextGen 3 LEDs With Motion - Aerial Drone Shot. An actual LED Parking Lot Light Installation complete with aerial drone footage. Replaced 250w and 400watt metal halide with 12x 150 watt NextGen III LED Parking Lot Lights and 2 watt NextGen III LED Parking Lot Lights. 8 on poles with arm mounts and 6 on the building Compare light brightness, fc readings, light quality, energy costs, maintenance costs, install notes and more.
FEATURES
Remote for 5.8ghz Microwave Motion Sensor (select models of NextGen III and others, see SKU list)
1 remote can program many lights
Can be used as an on/off light with remote
Memory settings in remote.
Built in lights on remote for easy visual on where the setting is at.
1 remote can program all lights. So you only need 1-2 (a spare) for each installation. Please purchase at least 1 or the lights may not operate as desired.
USAGE AND SETUP TIPS
Requires 2 quantity AAA Batteries (not included)
Best to use remote at night or dusk. Remote lights (on the remote itself) may be hard to see and IR distance is better. Easier to see light onboard the sensor as well.(sensor has a single light indicating command received).
Remote is IR (infrared) based; distance average of 30 feet indoors. Requires direct line of sight. (no glass, no interference, new batteries). NOTE: Sunlight, electromagnetic ballasts, and similar etc will reduce the remote distance to under 10'. We recommend you program lights above 20' before coming down or attempting again at night and closer.
Brightness Settings: 70%/80%/90%/100% . This is brightness level for WITH motion or just on.
Daylight Settings 10lx, 30lx, 50lx, 100lx (use a lower setting if the light is coming on too early or on cloudy days. If its coming on at 10lx on a dark day that will be normal) NOTE: daylight delay is 3 minutes. This means changes in light will take 3 minutes to be seen. If programming for dusk to dawn settings, you will need to wait 3 minutes before it responds. The long delay avoids it going on and off with headlights or other lighting changes.
Hold Time at Brightness Setting with Motion: 10s/1Min/10Min/30Min
Sensitivity Settings: 20%/50%/75%/100%. Note: The 100% max distance can be up to 50' but may pick up plants in the wind or other objects blowing. The sensor beam angle comes out around 100 degrees wide, so similar/slightly narrower to the light pattern.
Standby Dim Level: 10%/20%/30%/50%
Standby Dim Time: infinite (always some light) /1Min/30Min/60Min
Test button for testing motion sensitivity. 3 sec hold time with motion when in Test mode.
About RuggedGrade Lighting
Rugged Grade Lighting is a California, USA owned and operated commercial lighting manufacturer. All of our sales and support is based in the USA and unlike others, we will be here for the long term. We are committed to designing only premium LED products and backing them up with better support and service. Our motto is Industrial Grade Solutions because our lights are built better and last longer.
Designed in the USA. Copyright 2012-2025
Before Choosing This Fixture
Use SKU 79-143 when confirming the configuration. Check the published voltage and mounting interface, identify separately ordered accessories, and confirm availability before planning installation.
Use the Fixture Order Checklist · Read the Specifications